Associated-equipment 6044 Bedienungsanleitung PDF herunterladen

ASSOCIATED

BEST 6044

BATTERY TESTER

OPERATOR AND SAFETY MANUAL

The BEST 6044 is designed to test electrical systems on 12, 12/24, and 24 volt vehicles. It can test and evaluate

starters, batteries, alternators, regulators, wiring connections, and other electrical equipment in the low voltage circuits

in the vehicle. Before operating this unit, thoroughly familiarize yourself with the safety instructions included in this

booklet and in the service manual.

External Voltage

Amp Probe

MODEL 6044

BATTERY ELECTRICAL SYSTEM TESTER

DOWN

ASSOCIATED

TEST SELECTION

BATTERY

ALTERNATOR

MIN.

VOLTS

FAULT

LOAD

MAX.

AMPS

LOAD

AMPS

LOAD

SETTING

START TEST

RESET

STARTER

TABLE OF CONTENTS

Features.......................................................................... 1

Safety instructions........................................................... 2

Battery Load Tests.......................................................... 3

Starter Tests ................................................................... 5

Charging System Tests................................................... 5

Troubleshooting Hints ..................................................... 7

Assembly Instructions ..................................................... 8

FEATURES OF THE BEST 6044 INCLUDE:

 Large, easy to read, LED digital AMPS and

VOLTS meters. The VOLTS meter reads voltages

to ±40 volts DC when reading the differential

voltage and up to 40.0 volts DC for the battery

voltage. The AMPS meter reads DC currents up

to 999 amps.

 The input impedance of the differential voltage is 2

megohms for accurate testing of solid state

circuits.

 The load is rated 500 amps on 12 volt batteries for

load testing batteries up to 1000 CCA capacity.

 Fixed loads designed to insure longer life.

 Amp probe zero button allows for maximum

accuracy in AMPS reading.

 LOAD ON light indicates the load is actuated and

serves as a reminder to not disconnect leads while

load is on.

 AMPS meter reads both + and - amps for easy

diagnosis of leakage current problems.

 Unit monitors the voltage ripple letting you know

when alternator output diodes have failed.

 The electronic circuits are protected against

reverse voltages caused by connecting leads

incorrectly.

 The electronic circuit board has a protective

coating to prevent damage and meter inaccuracy

due to moisture and dirt.

 Heavy duty leads are single extended so that they

may be used for testing at points up to 15 feet

apart.

 The clamps on the heavy duty lead are vinyl

dipped and have a flexi-spring stain relief to

prevent cable damage. Solid copper jaws provide

better electrical conduction and are field

replaceable.

 Heavy duty leads have internal tracer lead wires

for voltage reading the battery voltage. These

leads should not be attached to any voltage source

that could rise above 45 VDC.

 The light gauge voltage sensing leads (red and

black) have small test clips to allow testing at

points where the heavy duty leads can not reach.

Use the leads when the unit is set for the external

voltage (differential voltage) reading. The leads

can test points in a vehicle up to 15 feet apart and

read voltages up to 40 VDC.

 The inductive AMP PICKUP has 10 foot long lead

to allow for testing in hard to reach areas.

 All leads are long enough to test trucks, "high-rise"

four wheel drive, or off road vehicles.

 The optional cart has a long wheel-base for

greater stability when moved over rough surfaces

or cracked floors.

 Optional printer: prints a report of all the results of

any test performed by the 6044.

1 2 3 4 5 6 7

Inhaltsverzeichnis

Seite 1 - BATTERY TESTER

1 ASSOCIATEDBEST 6044 BATTERY TESTER OPERATOR AND SAFETY MANUAL The BEST 6044 is designed to test electrical systems on 12, 12/24, and 24 volt vehi

Seite 2 - + -+

2 IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS. The safety information contained herein should be reviewed every time the unit is used. BA

Seite 3 - BATTERY LOAD TESTS

3 BATTERY LOAD TESTS TESTING 12 VOLT BATTERIES: The standard battery load test is to apply a load on the battery equal to ½ the cold cranking amp

Seite 4 - FIGURE 6

4 USE THIS SECTION FOR BATTERY TESTING IF YOUR 12/24 VOLT SYSTEM LOOKS SIMILAR TO THIS:  One six volt battery by itself cannot be tested with thi

Seite 5 - CHARGING SYSTEM TESTS

5 STARTER TESTS  Current draw of the starter, battery voltage, and voltage drop of leads can be measured when connected as shown (See figure 8).

Seite 6 - FIGURE 10

6 ALTERNATOR TEST SET UP: 1) Connect tester to battery as shown in (see figure 9). Press the Test Selection [2] button until the Alternator LED is

Seite 7 - 6044 TROUBLESHOOTING HINTS:

7 The AEC 132-0137 (6043) Amp-Probe may also be used independently of the 6044. Plug the insulated jacks into a standard digital Multimeter and

Kommentare zu diesen Handbüchern

Keine Kommentare

Associated-equipment 6044 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Ausrüstung Associated-equipment 6044 herunter. Associated Equipment 6044 User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Ausrüstung Associated-equipment 6044