Associated-equipment 6042 Bedienungsanleitung PDF herunterladen

ASSOCIATED

BEST 6042

ATTERY ELECTRICAL SYSTEMS TESTER

OPERATOR AND SAFETY MANUAL

The B.E.S.T. tester is designed to test electrical systems on 12, 12/24, and 24 volt vehicles. It can test and evaluate

starters, batteries, alternators, regulators, wiring connections, and other electrical equipment in the low voltage

circuits in the vehicle. Before operating this unit, thoroughly familiarize yourself with the safety instructions included in

this booklet and in the service manual.

TABLE OF CONTENTS

Features.......................................................................1

Safety instructions .......................................................2

Battery Load Tests.......................................................3

Starter Tests ................................................................5

Charging System Tests ...............................................5

Trouble Shooting Hints................................................7

Assembly Instructions..................................................8

FEATURES OF THE B.E.S.T. INCLUDE:

 Large, easy to read, LED digital AMPS and

VOLTS meters. The VOLTS meter reads voltages

to ±99.9 volts DC on the EXT position and up to

35.0 volts DC on the INT position. The AMPS

meter reads DC currents up to 999 amps.

 The input impedance of the meters is 10 Meg

ohms for accurate testing of solid state circuits.

 The carbon pile is rated 500 amps on 12 volt

batteries for load testing batteries up to 1000 CCA

capacity.

 Curved carbon discs allow better low end

resolution of current and longer life.

 AMPS ZERO ADJUST allows for maximum

accuracy in AMPS reading.

 LOAD ON light indicates the carbon pile is

actuated and serves as a reminder to turn the load

off (full counter-clockwise position).

 AMPS meter reads both + and - amps for easy

diagnosis of leakage current problems.

 DEFECTIVE DIODE indicator light lets you know

when alternator output diodes or GM diode trios

have failed.

 The electronic circuits are protected by a fuse

against excessive voltage inputs that will damage

the unit. LED indicators on the circuit board allow

for easy diagnosis of fuse or other problems.

 The electronic circuits are protected against

reverse voltages caused by connecting leads

incorrectly.

 The electronic circuit board has a protective

coating to prevent damage and meter inaccuracy

due to moisture and dirt.

 The FIELD selector switch is spring loaded and

always returns to an off position so there is no

power on the field lead when not in use.

 The field wire (blue) is supplied to allow for

regulator trouble shooting. The lead may be

switched to negative (A) or positive (B) polarity

depending on the application. The lead has a

circuit breaker in it to prevent damage if

accidentally shorted out when in use.

 Heavy duty leads are single extended so the may

be used for testing at points up to 15 feet apart.

 The clamps on the heavy duty lead are vinyl

dipped and have a flexi-spring stain relief to

prevent cable damage. Solid copper jaws provide

better electrical conduction and are field

replaceable.

 Heavy duty leads have internal tracer lead wires

for voltage readings where the clamps are

attached when the VOLTS switch is in the internal

(INT) position. These leads should not be

attached to any voltage source that could rise

above 35 VDC.

 The light gauge voltage sensing leads (red and

black) have small test clips to allow testing at

points where the heavy duty leads can not reach.

Use the leads when the VOLTS switch is in the

external (EXT) position. The leads can test points

in a vehicle up to 15 feet apart and read voltages

up to 99.9 VDC.

 The inductive AMPS PICKUP has 10 foot long

lead to allow for testing in hard to reach areas.

 All leads are long enough to test trucks, "high-rise"

four wheel drive, or off road vehicles.

 The cart has a long wheelbase for greater stability

when moved over rough surfaces or cracked

floors.

ASSOCIATED

6042

VOLTSFIELD

LOAD

DEFECTIVE

DIODE

AMP

ADJUST

LOAD ADJUST

AMPSVOLTS

SAFETY INSTRUCTION

1 2 3 4 5 6 7 8

Inhaltsverzeichnis

Seite 1 - BEST 6042

ASSOCIATED BEST 6042 B 1 ATTERY ELECTRICAL SYSTEMS TESTER OPERATOR AND SAFETY MANUAL The B.E.S.T. tester is designed to test electrical systems on 1

Seite 2 - + -+

IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS. The safety information contained herein should be reviewed every time the unit is used. BATTER

Seite 3 - BATTERY LOAD TESTS

BATTERY LOAD TESTS TESTING 12 VOLT BATTERIES: 1) The standard battery load test is to apply a load on the battery equal to ½ the cold cranking amp (

Seite 4 - FIGURE 7

USE THIS SECTION FOR BATTERY TESTING IF YOU’RE 12/24 VOLT SYSTEM LOOK SIMILAR TO THIS:  One six volt battery by itself cannot be tested with this u

Seite 5 - CHARGING SYSTEM TESTS

5 STARTER TESTS  Current draw of the starter, battery voltage, and voltage drop of leads can be measured when connected as shown (See figure 8).

Seite 6 - FIGURE 10

6 OUTPUT VOLTAGE TEST: 1) Connect tester to battery as shown. Connect AMPS PICKUP around positive output cable of alternator. If wires split off

Seite 7 - ASSEMBLY INSTRUCTIONS

7 A GM ALTERNATOR HAS A DIFFERENT PROCEDURE FOR FULL FIELDING:1) Locate a "D" shaped hole in the rear of the alternator. 2) Insert a sm

Seite 8 - Figure 2

8 ASSEMBLING THE CART: 1. Place lower tray (1) and upper tray (2) on flat surface. Align the lower holes in back leg (3) with holes in lower tray

Kommentare zu diesen Handbüchern

Keine Kommentare

Associated-equipment 6042 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Ausrüstung Associated-equipment 6042 herunter. Associated Equipment 6042 User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Ausrüstung Associated-equipment 6042